Author Topic: Chubbys meat mallet stem project (Read 3567 times)

oldschoolace · « **on:** May 04, 2017, 08:44 PM »

Its been a while since i have made owt and with the workshop finally dry after the biblical flood i thought it was time i got round to honouring a promise to Rich for something a little different for his next build.

Started with the usual big block of ali with holes drilled for the stem shaft and bars

In my wisdom i decided a stem cap that bolted on from the rear might be fun and wouldnt interupt the desired meat mallet look at the front

half a day drilling 4 very long and neat holes and running the stem nervously through my woodwork router resulted in this.

I decided the other end needed a wide axe/wedge/bone crushing look to it. This also had the nice effect of revealing the long bolt holes

Just need to cut through the bar section, fit a post and give it a final finish and iits all done

griff · « **Reply #1 on:** May 04, 2017, 09:23 PM »

That's ace

Wasted on Rich though as he's a vegetarian

Andyboy77 · « **Reply #2 on:** May 04, 2017, 09:28 PM »

This is such a cool project Clint! I can't wait seeing it fitted to Richs bike

Jaymz · « **Reply #3 on:** May 04, 2017, 09:32 PM »

Top job Clint

chubby · « **Reply #4 on:** May 04, 2017, 10:03 PM »

Feel like I need to put it on something better now

rooski · « **Reply #5 on:** May 04, 2017, 10:17 PM »

Good work

, what did you use to cut the serrations, did you say a router

oldschoolace · « **Reply #6 on:** May 04, 2017, 11:02 PM »

One of these in a router table

Do not try this at home kids

In2bmx · « **Reply #7 on:** May 05, 2017, 08:35 AM »

Awesome work as normal Clint

CustardLips · « **Reply #8 on:** May 05, 2017, 08:52 AM »

Nice bit of precision engineering there Clint.

NORTY40 · « **Reply #9 on:** May 05, 2017, 09:58 AM »

Great work Clint

insectbones · « **Reply #10 on:** May 06, 2017, 10:19 AM »

Top work there

dp and chopper dude · « **Reply #11 on:** May 06, 2017, 07:49 PM »

I absolutely bloody love that. It's ACE

MartyC · « **Reply #12 on:** May 07, 2017, 05:16 AM »

Pretty impressive work

oldschoolace · « **Reply #13 on:** May 13, 2017, 11:34 AM »

She is all done

Rich wanted it leaving the raw machine finish which i think looks ace too

griff · « **Reply #14 on:** May 13, 2017, 12:38 PM »

Top work Clint

chubby · « **Reply #15 on:** May 13, 2017, 04:15 PM »

Fooookin mega

dancetothedrummersbeat · « **Reply #16 on:** May 13, 2017, 08:00 PM »

Amazing work Clint, nice one. Great to see you today

rooski · « **Reply #17 on:** May 13, 2017, 10:44 PM »

Brutalist, and all the better for it, good work

chubby · « **Reply #18 on:** May 18, 2017, 11:46 AM »

Looks fookin ace, so chuffed & such a lucky boy. Can't thank Clint enough for making it, best get my ass down to St Ives brewery sharpish 😁😁

Sent from my HTC One M9 using Tapatalk

In2bmx · « **Reply #19 on:** May 18, 2017, 12:43 PM »

Nice work

CustardLips · « **Reply #20 on:** May 18, 2017, 02:04 PM »

That's a beast of a stem.

Gary72 · « **Reply #21 on:** May 18, 2017, 07:04 PM »

Ton job

poolysheriff · « **Reply #22 on:** May 18, 2017, 08:40 PM »

Clever boy , Clint

dancetothedrummersbeat · « **Reply #23 on:** May 18, 2017, 08:51 PM »

Great work

deeman · « **Reply #24 on:** May 19, 2017, 12:07 AM »

That is the nuts Clint....my mind is blown with the design

Author Topic: Chubbys meat mallet stem project (Read 3567 times)

griff

In2bmx

griff

In2bmx