RADBMX.CO.UK

Technical & Reference Section => Tech and Restoration => Topic started by: monkian on February 23, 2016, 05:56 PM

Title: Tange MX-3 ID Guide
Post by: monkian on February 23, 2016, 05:56 PM: Ad from BMXA-80/06 8)

(http://i72.photobucket.com/albums/i175/vimto_uk/Reference/tange-mx3-BMXA-8006_zps987e7274.jpg)

The top nut wasn't stamped but they had a colour coded locking washer (Blue Strip - Blue Washer, Black Strip - Black Washer etc) same story with the Tange MX-5. I've seen snide Tange stamped top nuts coupled with YST80's being passed off as MX-3's but YST quality is shocking when compared like for like. I'm pretty sure Tange bearing races held more bearings than YST as well but not 100% sure on that.

Apparently there's a slightly different size nut on the Adjusting Cup & Top Nut. Tange MX-3 fits 30mm perfectly but YST is a bit out (maybe imperial)??

(https://farm3.staticflickr.com/2446/3544448105_729bfeef49_b.jpg)

MX-3 (left) V's YST (right):
The YST Adjusting Cup isn't as high:

(http://i944.photobucket.com/albums/ad289/da_blair/Parts%20Reference/MX-3vYST80_zps9a7687e6.jpg)

MX-3 (top) V's YST (bottom):
The YST also has a larger flat area around the nut part of the Adjusting Cup:

(http://uploads.tapatalk-cdn.com/20160828/1fc717e1baff743e011c7016af4ddb35.jpg)

Tange MX-3 Components:
Adjusting Cup / Lower Stationary Cup Weights (allow for tolerance of 1-2g).

(http://i72.photobucket.com/albums/i175/vimto_uk/Reference/image1-3_zpsr6cxozol.jpg)

(http://i72.photobucket.com/albums/i175/vimto_uk/Reference/image2-3_zpspy9j7d7y.jpg)

(http://uploads.tapatalk-cdn.com/20160228/5ddd9ec246a3b416fe45fa3b51d1fec3.jpg)

Inside Pics (both Tange shown):
Note: Shallow threaded area, x3 distinct internal areas (flat - bearing seat - cup wall).
Also really neat holes (no burrs or rough edges).

(http://i72.photobucket.com/albums/i175/vimto_uk/Reference/image3_zps4mofzjhk.jpg)

(http://i72.photobucket.com/albums/i175/vimto_uk/Reference/image4_zpsxdrhxgv6.jpg)

MX-3 (top) V's YST (bottom):

(http://uploads.tapatalk-cdn.com/20160828/3a3316d78dba32d8324f306dc56b30e7.jpg)

Other Notes:
On other fakes, I've noticed the Adjusting Cup has been heavier than the Tange part.
The Lower Stationary Cup has also been lighter. Both these fake parts also looked different on the inside.

Tangetastic. Hope it helps 8) :daumenhoch:
Title: Re: Tange MX-3 ID Guide
Post by: HUTCHMAN on February 23, 2016, 06:19 PM: An MX 3 was the very first "part" i ever bought, back probably 81/82.. still got it to this day. Happily sitting on my Race inc RM2. Still looks in the same condition as the day i first bought it(no cracks or pitting what so ever) :smitten:
Title: Re: Tange MX-3 ID Guide
Post by: Mikku on February 24, 2016, 12:28 AM: Great work Paul! :bow:

Tange = good quality! I always new that bitd (a Laserlite immediately springs to mind) but my appreciation has grown since then, plus I now have the added connection of living in the same country. As an interesting side note, I had always thought and pronounced the name as rhyming with the word "flange". However, now I've a basic level of Japanese under my belt, I realise that it's actually pronounced differently, and should sound more like "tan-gay" :daumenhoch:
Title: Re: Tange MX-3 ID Guide
Post by: 58 delray on February 24, 2016, 11:30 AM: nice thread Paul, some really good info there, especially with all the snide stuff about, thanks :daumenhoch:
Title: Re: Tange MX-3 ID Guide
Post by: NORTY40 on February 24, 2016, 02:34 PM: Nice one Paul :daumenhoch:
Title: Re: Tange MX-3 ID Guide
Post by: BMX1973 on February 24, 2016, 08:54 PM: :coolsmiley:
Title: Re: Tange MX-3 ID Guide
Post by: monkian on February 25, 2016, 03:59 PM: Thanks lads. I hope it proves useful ;)
Title: Re: Tange MX-3 ID Guide
Post by: sawzall on February 25, 2016, 08:41 PM: :daumenhoch:
Title: Re: Tange MX-3 ID Guide
Post by: monkian on August 28, 2016, 11:27 PM: Just added a couple more comparison pics ;)
Title: Re: Tange MX-3 ID Guide
Post by: animal on August 29, 2016, 01:43 PM: Excellent work ;)