gfxgfx
 
logo
 
gfx gfx
gfx
975804 Posts in 138943 Topics by 6363 Members - Latest Member: V6 DOW November 22, 2024, 06:12 PM
*
gfx* Home | Portal | Forum | Merchandise | Help | Login | Register | gfx
gfx
RADBMX.CO.UK  |  Technical & Reference Section  |  Tech and Restoration  |  Tuff neck stem problem....
gfx
gfxgfx
 

Author Topic: Tuff neck stem problem....  (Read 4348 times)

0 Members and 1 Guest are viewing this topic.

Offline Bob_Acid

  • Team Admin
  • BMX Overlord
  • *
  • Posts: 17364
  • It's Bronked
  • Rated:
Tuff neck stem problem....
« on: August 03, 2005, 05:23 PM »
i've put my Tuff neck on the Torker and there is about a 6-7 mil gap between the headset and the bottom of the stem as if the shaft on the stem is too long for the forks. Is there spacers/ washers or something i can use for 1" headsets?

Does anyone know if i use the tange lock might that take up the difference being that much bigger than the basic nut?

Cheers.
« Last Edit: August 03, 2005, 05:26 PM by Bob_Acid »

Offline stuntmaster

  • 540 Air
  • *******
  • Posts: 2529
  • Rated:
Re: Tuff neck stem problem....
« Reply #1 on: August 03, 2005, 05:45 PM »
you sure the old stem bolt is not stuck in stem ,i had that on a skyway once also have had this on a few forks ie as the stem get lower in shaft the stem stops and does not go down anymore .it`s the forks that have the problem ie shaft gets smaller as the stem goes in normally where they weld the legs on .try this and that will tell you if forks are the problem and not stem.
i can`t see a way of fixing this only cut down the stem shaft so it`s not as long but mmm not a tuf neck .
no1stuntmaster on instagram

Offline Bob_Acid

  • Team Admin
  • BMX Overlord
  • *
  • Posts: 17364
  • It's Bronked
  • Rated:
Re: Tuff neck stem problem....
« Reply #2 on: August 03, 2005, 06:01 PM »
i think it is the forks paul.

Offline stuntmaster

  • 540 Air
  • *******
  • Posts: 2529
  • Rated:
Re: Tuff neck stem problem....
« Reply #3 on: August 03, 2005, 06:17 PM »
my old 80 mongoose had that problem ,i had to cut shaft down on stem to fix .
no1stuntmaster on instagram

Offline Rombloke

  • Team Owner
  • My life is Radbmx
  • *
  • Posts: 77337
  • do one
  • Rated:
Re: Tuff neck stem problem....
« Reply #4 on: August 03, 2005, 06:33 PM »
shims from ots bob...under or on top of the lock nut....prob a few pennies each

dave
haro, how do you do

Sanmarcopizza

  • Guest
Re: Tuff neck stem problem....
« Reply #5 on: August 03, 2005, 07:25 PM »
I have had worse problems with a number os stems of the Pro Neck, Tuff Neck, DK variety in redline frames. They sit about an inch high. As mentioned below, it's the forks that taper inside.

Offline Waxintaxin

  • Team Owner
  • Cherry Picker
  • *
  • Posts: 1090
  • Rated:
Re: Tuff neck stem problem....
« Reply #6 on: August 03, 2005, 08:05 PM »
They squeek all the way down anyway

Offline ORB

  • Founding Fathers
  • My life is Radbmx
  • *
  • Posts: I am a geek!!
  • Rated:
Re: Tuff neck stem problem....
« Reply #7 on: August 03, 2005, 08:37 PM »
12

spinmaster

  • Guest
Re: Tuff neck stem problem....
« Reply #8 on: August 05, 2005, 09:34 AM »
was that drawn in photoshop orb?

Offline Rombloke

  • Team Owner
  • My life is Radbmx
  • *
  • Posts: 77337
  • do one
  • Rated:
Re: Tuff neck stem problem....
« Reply #9 on: August 08, 2005, 06:01 PM »
no jim...its a real photo on black and white film????

Dave
haro, how do you do

spinmaster

  • Guest
Re: Tuff neck stem problem....
« Reply #10 on: August 08, 2005, 06:05 PM »
taken using a night vision lense?

Offline Rombloke

  • Team Owner
  • My life is Radbmx
  • *
  • Posts: 77337
  • do one
  • Rated:
Re: Tuff neck stem problem....
« Reply #11 on: August 08, 2005, 06:37 PM »
without a doubt!!!!
haro, how do you do

RADBMX.CO.UK  |  Technical & Reference Section  |  Tech and Restoration  |  Tuff neck stem problem....
 

gfxgfx
gfx gfx
Powered by MySQL Powered by PHP Valid XHTML 1.0! Valid CSS!
SimplePortal 2.3.5 © 2008-2012, SimplePortal