gfxgfx
 
logo
 
gfx gfx
gfx
975794 Posts in 138943 Topics by 6362 Members - Latest Member: Bmxflex November 14, 2024, 11:52 AM
*
gfx* Home | Portal | Forum | Merchandise | Help | Login | Register | gfx
gfx
RADBMX.CO.UK  |  Technical & Reference Section  |  Tech and Restoration  |  removing crank arms
gfx
gfxgfx
 

Author Topic: removing crank arms  (Read 1980 times)

0 Members and 1 Guest are viewing this topic.

2020mad

  • Guest
removing crank arms
« on: December 24, 2005, 07:52 PM »
any one got any tips how to remove a set of profile crank arms without damaging arms or bike they are stuck on had soaking in wd40 all day and still cant get them off. cheers

Offline Rombloke

  • Team Owner
  • My life is Radbmx
  • *
  • Posts: 77337
  • do one
  • Rated:
Re: removing crank arms
« Reply #1 on: December 24, 2005, 09:56 PM »
profile removal tool.....7 quid

easy

Dave
haro, how do you do

Offline TwoBobRob

  • Site Supporter
  • 900 Air
  • *
  • Posts: 3713
  • Rated:
Re: removing crank arms
« Reply #2 on: December 24, 2005, 10:35 PM »
You may end up sacrificing the bolts,  but you can wind them out a turn or two, steady the frame and then beat the crap out of them.  Something will move..... ;)   Check to see if the gap has changed, wind the bolt out another turn or two and continue.  Noisy, but effective  :)

TOMMY2WHEEL

  • Guest
Re: removing crank arms
« Reply #3 on: December 29, 2005, 03:09 AM »
Crank puller or removal tool are the best to use. they seperate the arm from the shaft evenly with minimal ware to the splines or wedges. use what the crank manufacture suggest.

weston

  • Guest
Re: removing crank arms
« Reply #4 on: December 29, 2005, 09:19 AM »
there was no way of getting the one from my old bike. i had to saw through the spindle to get it off..

greentoad

  • Guest
Re: removing crank arms
« Reply #5 on: December 29, 2005, 12:10 PM »
Hi  :santa_wink:

If you do get stuck it might be worth visiting a local garage (if you know one) and using a puller, or buy one. They are quite handy.

http://buy1.snapon.com/catalog/catalog1.asp'tool=all&Cat_ID=124110&Cat_NAME=Pullers&store=uk

Example the 2 or 3 Jaw Pressure Screw -

http://buy1.snapon.com/catalog/item.asp?P65=&tool=all&item_ID=9952&group_ID=1171&store=uk&dir=catalog

It is most important to give the item a good soak, and then start to undo very slowly then tighten a little, spray then undo, tighten etc...

I also did a post a while back, and the Freeze Spray is very effective and is used on Large / Heavy Machinery down to small bolts etc when out in the field. That really is a must thing to have.

Hope this helps

greentoad

wirewheel

  • Guest
Re: removing crank arms
« Reply #6 on: January 11, 2006, 01:17 AM »
like the man says, usa the right tool, a profile tool no other way without fooking something up.

Offline diesel

  • Look Back
  • *****
  • Posts: 1594
  • Rated:
Re: removing crank arms
« Reply #7 on: January 11, 2006, 08:53 AM »
Here's what I use... Its very effective!

I use a medium size socket set extension bar that fits neatly into the end of the crank arm and dosent touch the sides. I then lay  the bike down onto some wood covered with towels. and give it a couple of hits with a hammer. If its really stuck in there proper, you maybe want to stand the bike up rather than lay it down. Put the towels round your legs instead and brace the bike against them.

It pops out nice and easily!

Offline ORB

  • Founding Fathers
  • My life is Radbmx
  • *
  • Posts: I am a geek!!
  • Rated:
Re: removing crank arms
« Reply #8 on: January 11, 2006, 10:51 AM »
hammer is the best method of fixing anything, even a slow puncture.
12

2020mad

  • Guest
Re: removing crank arms
« Reply #9 on: January 11, 2006, 02:21 PM »
They wanted £16 at my local bike shop for removal tool so going to try diesels method tonight.

Offline TwoBobRob

  • Site Supporter
  • 900 Air
  • *
  • Posts: 3713
  • Rated:
Re: removing crank arms
« Reply #10 on: January 11, 2006, 08:51 PM »
Just be a little bit careful bashing a socket with a hammer...  If its a chemical black impact socket with thick sidewalls, then whack away  ;)  but if its your regular chrome cheapy, they have been known to shatter.... Not often but I have seen in happen.   :)

Offline ORB

  • Founding Fathers
  • My life is Radbmx
  • *
  • Posts: I am a geek!!
  • Rated:
Re: removing crank arms
« Reply #11 on: January 11, 2006, 09:13 PM »
my mate has a glass eye from smacking a crankshaft with a hammer.
12

Offline TwoBobRob

  • Site Supporter
  • 900 Air
  • *
  • Posts: 3713
  • Rated:
Re: removing crank arms
« Reply #12 on: January 11, 2006, 09:27 PM »
..........is exactly what I'm on about...... a little caution there chap   :daumenhoch:

Sanmarcopizza

  • Guest
Re: removing crank arms
« Reply #13 on: January 12, 2006, 09:07 AM »
my mate has a glass eye from smacking a crankshaft with a hammer.

And I bet you bore it to sleep.

Offline oberonspacefruit

  • BMX Legend
  • Hoffman's Love Child
  • *
  • Posts: 24549
  • Rated:
Re: removing crank arms
« Reply #14 on: January 12, 2006, 10:20 AM »
lmao!!!!!
I want to touch ORB

Offline jT Racing

  • BMX Overlord
  • ***********
  • Posts: 17338
  • i like bikes. :/
  • Rated:
Re: removing crank arms
« Reply #15 on: January 12, 2006, 10:56 AM »
piece of bar or socket just amller than the opening, big hammer, tap tap tapppy tap whack.
ding dong

RADBMX.CO.UK  |  Technical & Reference Section  |  Tech and Restoration  |  removing crank arms
 

gfxgfx
gfx gfx
Powered by MySQL Powered by PHP Valid XHTML 1.0! Valid CSS!
SimplePortal 2.3.5 © 2008-2012, SimplePortal