gfxgfx
 
logo
 
gfx gfx
gfx
975792 Posts in 138942 Topics by 6363 Members - Latest Member: Bmxflex November 12, 2024, 01:05 AM
*
gfx* Home | Portal | Forum | Merchandise | Help | Login | Register | gfx
gfx
RADBMX.CO.UK  |  Technical & Reference Section  |  Tech and Restoration  |  stripping powder coating
gfx
gfxgfx
 

Author Topic: stripping powder coating  (Read 682 times)

0 Members and 1 Guest are viewing this topic.

little7251

  • Guest
stripping powder coating
« on: July 06, 2007, 09:56 AM »
as the title says any ideas how to do this do i use normal paint stripper or what help!! :daumenhoch: :4_17_5: :Great_Britain:

theRuler

  • Guest
Re: stripping powder coating
« Reply #1 on: July 06, 2007, 10:58 AM »
nitromors will do it.

but not anywhere near as fast as it does on rattle can paint.

it's a long job

if it's just a set of forks, then plod on. but a whole frameset? i'd leave it on. spray over it.

little7251

  • Guest
Re: stripping powder coating
« Reply #2 on: July 06, 2007, 11:03 AM »
can superbike dan coat over it thats the question ?? cheers matey  :daumenhoch: :4_17_5: :Great_Britain:

theRuler

  • Guest
Re: stripping powder coating
« Reply #3 on: July 06, 2007, 11:10 AM »
should be able to

as long as it's flat

powder usually goes over anything!!

if he doesn't like to powder over powder, chances are he will have a good method up his sleeve on how to get it stripped

Offline Dark Diggler

  • Berm Worm
  • ***********
  • Posts: 12607
  • Rated:
Re: stripping powder coating
« Reply #4 on: July 06, 2007, 03:22 PM »
Shot blast................................................................

season.....................................................................

DONE  :daumenhoch:
Whats the matter Kid, don't ya like clowns? Don't we make you laugh? Aint we fukkin funny?

little7251

  • Guest
Re: stripping powder coating
« Reply #5 on: July 06, 2007, 03:25 PM »
man i tried nitro moors its going to take a while lucky i'm patient :daumenhoch: :4_17_5: :Great_Britain:

rarman1

  • Guest
Re: stripping powder coating
« Reply #6 on: July 06, 2007, 05:42 PM »
have a chat with dan about it mate,

it took me ages to strip my frames and dan needed to sand blast them anyway as there was still bits of paint in the welds and nooks & cranies,

dans a top bloke i'm sure he wont mind you asking him ;)

Offline MartyC

  • Berm Worm
  • ***********
  • Posts: 8755
  • Radder than a Rad thing on a Rad day; maybe?
  • Rated:
Re: stripping powder coating
« Reply #7 on: July 06, 2007, 06:01 PM »
With powder coat you can super-heat it or acid dip - I'm pretty certain Dan can do both so deffo worth dropping him a line  :daumenhoch:


Better to crash and burn than fade away

Offline Dingobmxer

  • Founding Fathers
  • 900 Air
  • *
  • Posts: 3639
  • Rated:
Re: stripping powder coating
« Reply #8 on: July 06, 2007, 06:28 PM »
Dan has an acid dip tank,
I just send him my old tatty stuff and it comes back stunning  :smitten:  :smitten:  :smitten:
 :) DINGO :)

Offline superbikedan

  • BMX Legend
  • 900 Air
  • *
  • Posts: 3819
  • Rated:
Re: stripping powder coating
« Reply #9 on: July 06, 2007, 07:41 PM »
ok guys  the answer to the questions,

yes i can powder over the original coat but don't like to as you loose definition in the

welds,  serial numbers ect,

acid strip is good but i find it lifts powder really quick but two pack takes ages :)

and shotblast is the best way but only fine shot ;)

and finally  i can sort out all three :coolsmiley:
For powder coating drop me a pm

little7251

  • Guest
Re: stripping powder coating
« Reply #10 on: July 06, 2007, 08:35 PM »
hi dan firstly i don' t know the paint code could u get a close match and secondly how much would it be for u to blast the frame and coat it cheers (steve) :daumenhoch: :4_17_5: :Great_Britain:

RADBMX.CO.UK  |  Technical & Reference Section  |  Tech and Restoration  |  stripping powder coating
 

gfxgfx
gfx gfx
Powered by MySQL Powered by PHP Valid XHTML 1.0! Valid CSS!
SimplePortal 2.3.5 © 2008-2012, SimplePortal