Author Topic: Why is my bike doing this to my sprockets (Read 2010 times)

xmisslucyx · « **Reply #1 on:** April 21, 2016, 06:33 PM »

Its not the teeth is where the spline goes its taking chunks of metal out of it

Sent from my XT1032 using Tapatalk

Jaymz · « **Reply #2 on:** April 21, 2016, 06:35 PM »

Something isn't tight, or you haven't got a top hat washer on the spindle taking up the gap between the 19mm spindle and 22mm sprocket hole

xmisslucyx · « **Reply #3 on:** April 21, 2016, 06:37 PM »

I've put 2 different the original and the eastan bike top hat and its still taking chunks out of it

Sent from my XT1032 using Tapatalk

Jaymz · « **Reply #4 on:** April 21, 2016, 06:39 PM »

Something isn't fitting right, there's play in it somewhere

xmisslucyx · « **Reply #5 on:** April 21, 2016, 06:39 PM »

I'll take a pic of my spline and set up

Sent from my XT1032 using Tapatalk

xmisslucyx · « **Reply #6 on:** April 21, 2016, 06:41 PM »

Jaymz · « **Reply #7 on:** April 21, 2016, 06:50 PM »

That picture is minus the top hat washer right?

xmisslucyx · « **Reply #8 on:** April 21, 2016, 06:50 PM »

Yes

Sent from my XT1032 using Tapatalk

xmisslucyx · « **Reply #9 on:** April 21, 2016, 06:51 PM »

xmisslucyx · « **Reply #10 on:** April 21, 2016, 07:00 PM »

My friend got the same set up as me and his sprocket is fine

Sent from my XT1032 using Tapatalk

xmisslucyx · « **Reply #11 on:** April 21, 2016, 07:05 PM »

I was gonna get a new chain new sprocket and back wheel but I don't see the point if my sprocket is getting wrecked

Sent from my XT1032 using Tapatalk

CustardLips · « **Reply #12 on:** April 21, 2016, 07:24 PM »

Looks messy... might be worth a trip to your LBS.

xmisslucyx · « **Reply #13 on:** April 21, 2016, 07:26 PM »

Lbs ?

Sent from my XT1032 using Tapatalk

CustardLips · « **Reply #14 on:** April 21, 2016, 08:41 PM »

Local bike shop.

xmisslucyx · « **Reply #15 on:** April 21, 2016, 08:41 PM »

Its not long come back from there

Sent from my XT1032 using Tapatalk

pickle · « **Reply #16 on:** April 21, 2016, 08:51 PM »

Are the washers to small allowing for small movements? Over time will wear away soft alloys??

xmisslucyx · « **Reply #17 on:** April 21, 2016, 08:52 PM »

No everything is where it should be

Sent from my XT1032 using Tapatalk

xmisslucyx · « **Reply #18 on:** April 21, 2016, 09:11 PM »

All the washers top hat pinch bolt spline and crank are new so I Idk why its doing it

Sent from my XT1032 using Tapatalk

MartyC · « **Reply #19 on:** April 24, 2016, 09:44 AM »

Have you checked the chain alignment? It looks like there is some movement in the tophat/chainring which is being exasperated by the chain alignment pulling it to one side. Does your chain go loose and tight as it rotates?

john4130 · « **Reply #20 on:** April 24, 2016, 10:57 AM »

it looks like the tophat washer is too small, probably a 22mm. try a 23.8mm one or 15/16" one in old money. it should be a tight fit into the chainring.

CustardLips · « **Reply #21 on:** April 24, 2016, 11:44 AM »

Quote from: xmisslucyx on April 21, 2016, 08:41 PM

Its not long come back from there

Don't take it back there then.

griff · « **Reply #22 on:** April 24, 2016, 05:25 PM »

Quote from: CustardLips on April 24, 2016, 11:44 AM

Quote from: xmisslucyx on April 21, 2016, 08:41 PM
Its not long come back from there

Don't take it back there then.

Wise words there

oldtired · « **Reply #23 on:** June 04, 2016, 09:07 AM »

when you put it together is the top hat sat inside the chainring? or on the outside of it?

Author Topic: Why is my bike doing this to my sprockets (Read 2010 times)

griff