gfxgfx
 
logo
 
gfx gfx
gfx
975808 Posts in 138943 Topics by 6370 Members - Latest Member: Robertflamn November 26, 2024, 09:27 PM
*
gfx* Home | Portal | Forum | Merchandise | Help | Login | Register | gfx
gfx
RADBMX.CO.UK  |  Technical & Reference Section  |  Tech and Restoration  |  Dumbass NS crank question
gfx
gfxgfx
 

Author Topic: Dumbass NS crank question  (Read 1378 times)

0 Members and 1 Guest are viewing this topic.

Offline WINI

  • Site Supporter
  • 900 Air
  • *
  • Posts: 3660
  • Sheeping it real ;-)
  • Rated:
Dumbass NS crank question
« on: April 15, 2012, 03:53 PM »
OK, so I'm a bit thick when it comes to 3 piece cranks as I never had a set BITD.  What are the consequences of not having a spacer between the two sealed bearings?

 :crazy2:
Neil, the bathroom's free. Unlike the country under the Thatcherite junta

Offline Discostu

  • 540 Air
  • *******
  • Posts: 2757
  • Two's Company
  • Rated:
Re: Dumbass NS crank question
« Reply #1 on: April 15, 2012, 04:30 PM »
When you tighten up the bolts at each end of the spindle it squeezes the two arms towards the bearings/cups/cones etc. if you don't have the correct tube spacer between the bearings then you put a side load on to them which makes them click.  (put the bearings/cups against the frame/bottom bracket and measure the distance between the two inner faces of the bearings)  then you have the size of tube required. Once this is in place then the arms will push against the tube in the centre. Not the bearing race.  :daumenhoch:

Offline Tonto

  • Curb Endo
  • **
  • Posts: 240
  • Rated:
Re: Dumbass NS crank question
« Reply #2 on: April 15, 2012, 04:35 PM »
The spacer holds the bearings apart so if u ride without it u will bust the bearings , put the cup and bearing in one side and just the cup in the other then measure inside from the fitted bearing to where the inside of the other bearing will be ad that is the size of the spacer u will need , if the spacer is too small then there should b an assortment of little spacers u can use and it's usualy better to go bigger by about a mm ;) hope that helps bud

Offline WINI

  • Site Supporter
  • 900 Air
  • *
  • Posts: 3660
  • Sheeping it real ;-)
  • Rated:
Re: Dumbass NS crank question
« Reply #3 on: April 15, 2012, 04:37 PM »
Thanks guys.  I have a spacer but stupidly put the bearings in and forgot the spacer.  I blame booze.

Gonna be a right arse getting one back out
Neil, the bathroom's free. Unlike the country under the Thatcherite junta

whatquid

  • Guest
Re: Dumbass NS crank question
« Reply #4 on: April 15, 2012, 04:41 PM »
ive never used the spacers as i couldnt be bothered to fit them in............but ive never had a problem, i suppose if its there you should use it......

Offline WINI

  • Site Supporter
  • 900 Air
  • *
  • Posts: 3660
  • Sheeping it real ;-)
  • Rated:
Re: Dumbass NS crank question
« Reply #5 on: April 15, 2012, 04:44 PM »
1 NOS frame + 1 large hammer + 1 large screwdriver = success  :D
Neil, the bathroom's free. Unlike the country under the Thatcherite junta

Offline Betty

  • 900 Air
  • ********
  • Posts: 3141
  • Rated:
Re: Dumbass NS crank question
« Reply #6 on: April 15, 2012, 04:45 PM »
If your cranks have pinch bolts on the arms, like redlines you'll be ok without the spacer

If not you need it in there  :daumenhoch:
2 minutes turkish...

Offline WINI

  • Site Supporter
  • 900 Air
  • *
  • Posts: 3660
  • Sheeping it real ;-)
  • Rated:
Re: Dumbass NS crank question
« Reply #7 on: April 15, 2012, 05:39 PM »
If your cranks have pinch bolts on the arms, like redlines you'll be ok without the spacer

If not you need it in there  :daumenhoch:

They do have the pinch bolts mark, I've managed to get the spacer in though with a bit of grunt  :daumenhoch:
Neil, the bathroom's free. Unlike the country under the Thatcherite junta

Offline Picklez

  • Cherry Picker
  • ****
  • Posts: 1160
  • Rated:
Re: Dumbass NS crank question
« Reply #8 on: April 15, 2012, 09:14 PM »
1 NOS frame + 1 large hammer + 1 large screwdriver = success  :D

Quality !!!  :LolLolLolLol: :LolLolLolLol: :LolLolLolLol:
**** WANTED: Early black Comp ST's, Mint Black Shotgun 2 or OG Suede Kashi Aero, Titrons, Black-White/White-Black RadKaps. Thank You ****

Offline rick1970

  • Look Back
  • *****
  • Posts: 1742
  • Rated:
Re: Dumbass NS crank question
« Reply #9 on: April 20, 2012, 08:16 AM »
I ran 3 piece cranks on my very first bmx in 1981  wait for it .............................  cotter pin cranks  :wtf: fookin epic fail   :LolLolLolLol:

mattuknc

  • Guest
Re: Dumbass NS crank question
« Reply #10 on: April 20, 2012, 08:26 AM »
1 NOS frame + 1 large hammer + 1 large screwdriver = success  :D
I prefer a socket extension piece, it's a little kinder to the cups than a screwdriver.  :daumenhoch:

Offline Spen69

  • Site Supporter
  • Tail Whip
  • *
  • Posts: 5646
  • It was less than TWELVE parsecs.... .
  • Rated:
Re: Dumbass NS crank question
« Reply #11 on: April 20, 2012, 10:51 AM »
Use a drift or a socket bar next time ya numpty!

Or gimme a call and i'll tell you over the phone so you don't need to ask newbie questions..... ;-)

Boardroom - are you ever coming back there bud? I have a new toy to thrash tomorrow >;-)
Still limping......

Offline WINI

  • Site Supporter
  • 900 Air
  • *
  • Posts: 3660
  • Sheeping it real ;-)
  • Rated:
Re: Dumbass NS crank question
« Reply #12 on: April 20, 2012, 11:55 AM »
Use a drift or a socket bar next time ya numpty!

Or gimme a call and i'll tell you over the phone so you don't need to ask newbie questions..... ;-)

Boardroom - are you ever coming back there bud? I have a new toy to thrash tomorrow >;-)

Hey, in the world of NS, I am a newbie!  ;)

Sure I'm coming back, just haven't got there the last couple or so times.  Been to TRM, Blackpool and Corby in the interim mind.  Last time there were too many there, didn't enjoy it as much  :daumenhoch:
Neil, the bathroom's free. Unlike the country under the Thatcherite junta

RADBMX.CO.UK  |  Technical & Reference Section  |  Tech and Restoration  |  Dumbass NS crank question
 

gfxgfx
gfx gfx
Powered by MySQL Powered by PHP Valid XHTML 1.0! Valid CSS!
SimplePortal 2.3.5 © 2008-2012, SimplePortal