Author Topic: mini BB removal (Read 1857 times)

TELLIS302000 · « **on:** June 29, 2011, 11:17 PM »

Righty.....as the title says!

Do you need a special tool to split the BB on these mini's? It doesnt have lock nuts etc....

Cant say ive done one like this before!

kuwahero · « **Reply #1 on:** June 29, 2011, 11:22 PM »

what does it look like. pics would be good

TELLIS302000 · « **Reply #2 on:** June 29, 2011, 11:29 PM »

here ya go.

curtispro · « **Reply #3 on:** June 30, 2011, 08:29 AM »

That looks like a sealed cartridge unit, you will need a special tool to remove that, it will come out in one piece, something like this you just need to get the right one

http://www.google.co.uk/products/catalog?q=bottom+bracket+removal+tool&hl=en&prmd=ivns&resnum=1&bav=on.2,or.r_gc.r_pw.&biw=1440&bih=837&um=1&ie=UTF-8&tbm=shop&cid=2603711978387087716&sa=X&ei=eSUMTtadC8O98gOtnLmeDg&ved=0CFkQ8gIwAQ

diesel · « **Reply #4 on:** June 30, 2011, 09:09 AM »

Your lucky that should be relatively easy to find a tool for.

I've been looking for a tool to fit this one for about a year now:

1mancity2 · « **Reply #5 on:** June 30, 2011, 12:45 PM »

Diesel are you using the BB again or getting a new one, if fitting a new you can get them out using a stillson wrench.

Spen69 · « **Reply #6 on:** June 30, 2011, 01:20 PM »

Antony - that's a standard tool so your LBS should be able to remove that easy.

Failing that get it into the fix-it gazeebo at MK and I'll get it out for you as I think Hootski's treasure chest of tools has one in there to fit it

Dark Diggler · « **Reply #7 on:** June 30, 2011, 01:31 PM »

Quote from: TELLIS302000 on June 29, 2011, 11:17 PM

Cant say ive done one like this before!

If you get a tool and have a go, remember that the drive side is a reverse thread

diesel · « **Reply #8 on:** June 30, 2011, 01:42 PM »

Quote from: 1mancity2 on June 30, 2011, 12:45 PM

Diesel are you using the BB again or getting a new one, if fitting a new you can get them out using a stillson wrench.

I would destroy it but I'm concerned I won't find a replacement

Dark Diggler · « **Reply #9 on:** June 30, 2011, 01:54 PM »

Quote from: diesel on June 30, 2011, 01:42 PM

Quote from: 1mancity2 on June 30, 2011, 12:45 PM
Diesel are you using the BB again or getting a new one, if fitting a new you can get them out using a stillson wrench.

I would destroy it but I'm concerned I won't find a replacement

Whats the bb shell width and spindle length?

diesel · « **Reply #10 on:** June 30, 2011, 02:07 PM »

Quote from: Dark Diggler on June 30, 2011, 01:54 PM

Quote from: diesel on June 30, 2011, 01:42 PM
Quote from: 1mancity2 on June 30, 2011, 12:45 PM
Diesel are you using the BB again or getting a new one, if fitting a new you can get them out using a stillson wrench.

I would destroy it but I'm concerned I won't find a replacement

Whats the bb shell width and spindle length?

I'll have to check that one

Dark Diggler · « **Reply #11 on:** June 30, 2011, 02:08 PM »

I would imagine its 68mm shell and 108 or 110 spindle width, both are readily available

dordymush · « **Reply #12 on:** June 30, 2011, 08:17 PM »

big hammer and chisel

TELLIS302000 · « **Reply #13 on:** June 30, 2011, 08:25 PM »

Bought a tool for it.

Damn it was tight (seized), had to get some heat on it and put the tool in the vice and basically turn the whole frame.

Its out now though.

Shimano bb-un52 needed, easily available on the net unless anyone here has one for sale??

Dingobmxer · « **Reply #14 on:** June 30, 2011, 08:26 PM »

Top one is a standard fitment for a shimano tool and about a fiver for a shop to take it out for ya

Dan bring the frame with you next time you are up and we can take it to sShokwave to get it out

Dingo

diesel · « **Reply #15 on:** June 30, 2011, 09:05 PM »

Cheers Mark, will give you a shout

The spindle is 125mm

The Bottom Bracket measures 65mm

Anyone any ideas what might fit this?

1mancity2 · « **Reply #16 on:** July 01, 2011, 06:57 AM »

Diesel have a look on here,

http://www.parktool.com/blog/repair-help/bottom-bracket-tool-selection

Dark Diggler · « **Reply #17 on:** July 01, 2011, 10:55 AM »

Quote from: diesel on June 30, 2011, 09:05 PM

Cheers Mark, will give you a shout

The spindle is 125mm

The Bottom Bracket measures 65mm

Anyone any ideas what might fit this?

I would say that the BB you have in there aint for single speed but for a triple, that spindle width would put the chainline out by a mile, as for the shell width 68mm should be fine. Have you tried some cranks on there to see how it shapes up?

diesel · « **Reply #18 on:** July 01, 2011, 11:31 AM »

Quote from: Dark Diggler on July 01, 2011, 10:55 AM

Quote from: diesel on June 30, 2011, 09:05 PM
Cheers Mark, will give you a shout

The spindle is 125mm

The Bottom Bracket measures 65mm

Anyone any ideas what might fit this?

I would say that the BB you have in there aint for single speed but for a triple, that spindle width would put the chainline out by a mile, as for the shell width 68mm should be fine. Have you tried some cranks on there to see how it shapes up?

I have some nice 165 cranks for it and they seem to line up fine, although now that you've said that I'm going to double check.

I had a chat with SBD a little while ago about masking it for spray - So I'm thinking I might risk it in the oven with the BB attached

As It works well I'm not sure I really want to thinker about with it too much.....

1mancity2 · « **Reply #19 on:** July 01, 2011, 12:16 PM »

Wet paint it no need for the oven then

Author Topic: mini BB removal (Read 1857 times)

curtispro

1mancity2

1mancity2

1mancity2